| WM8731L The UFB200FA40 insulated modules integrate two state-of-the-art International Rectifier's Ultrafast recovery rectifiers in the compact, industry standard SOT-227 package. The planar structure of the diodes, and the platinum doping lifetime control, provide a Ultrasoft recovery current shape, together with the best overall performance, ruggedness and reliability characteristics.
These devices are thus intended for high frequency applications in which the switching energy is designed not to be predominant portion of the total energy, such as in the output rectification stage of Welding machines, SMPS, DCDC converters. Their extremely optimized stored charge and low recovery current reduce both over dissipation in the switching elements (and snubbers) and EMI/ RFI. ...
WM8731L The ICX209AK is an interline CCD solid-state image sensor suitable for PAL color video cameras.Compared with the current product ICX069AK,sensitivity and saturation signal are improved drastically through the adoption of Super HAD CCD technology.High resolution is achieved through the use of Ye,Cy,Mg,and G complementary color mosaic filters.
This chip features a field period readout system and an electronic shutter with variable charge-storage time.
The package is a 10mm-square 14-pin DIP (Plastic). ...
WM8731L The DS3884A is one in a series of transceivers designed specifically for the implementation of high performance Futurebus+ and proprietary bus interfaces. The DS3884A is a BTL 6-bit Handshake Transceiver designed to conform to IEEE 1194.1 (Backplane Transceiver Logic-BTL) as specified in the IEEE 896.2 Futurebus+ specification. Utilization of the DS3884A simplifies the implementation of all handshake signals which require Wired-OR glitch filtering. Three of the six bits have an additional parallel Wired-OR filtered receive output giving a total of nine receiver outputs.
In Wired-OR applications, the glitch generated as drivers are released from the bus, is dependent upon the backplane and parasitic wiring components causing the characteristics of the glitch to vary in pulse width and amplitude. To accommodate this variation the DS3884A features two pins defined as PS1 and PS2 which allow selection of Four Different Filter Settings to optimize glitch filtering for a given situation. The REXT pin is issued in conjunction with the filtering circuitry and requires a 15K Ohm resistor to ground.
The DS3884A driver output configuration is an NPN open collector which allows Wired-OR connection on the bus. Each driver output incorporates a Schottky diode in series with its collector to isolate the transistor output capacitance from the bus thus reducing the bus loading in the inactive state. The driver also has high sink current capability. Backplane Transceiver Logic (BTL) is a signaling standard that was invented and first introduced by National Semiconductor, then developed by the IEEE to enhance the performance of backplane buses. BTL compatible transceivers feature low output capacitance drivers to minimize bus loading, a 1V nominal signal swing for reduced power consumption and receivers with precision thresholds for maximum noise immunity. The BTL standard eliminates settling time delays that severely limit TTL bus performance, and thus provide significantly higher bus transfer rates. The backplane bus is intended to be operated with termination resistors (selected to match the bus impedance) connected to 2.1V at both ends. The low voltage is typically 1V at 25 C, 125 C and 1.1V at -55 C. Separate ground pins are provided for each BTL output to minimize induced ground noise during simultaneous switching.
The device’s unique drive circuitry meets a maximum slew rate of 0.5V/ns which allows controlled rise and fall times to reduce noise coupling to adjacent lines. The transceiver’s high impedance control and driver inputs are fully TTL compatible. The receiver is a high speed comparator that utilizes a bandgap reference for precision threshold control allowing maximum noise immunity to the BTL 1V signaling level. Separate QVcc and QGND pins are provided to minimize the effects of high current switching noise. Output pins FR1-FR3 are the filtered outputs and R1-R6 are unfiltered outputs. All receiver outputs are fully TTL compatible.
The DS3884A supports live insertion as defined for Futurebus+ through the LI (Live Insertion) pin. To implement live insertion the LI pin should be connected to the live insertion power connector. If this function is not supported the LI pin must be tied to the Vcc pin. The DS3884A also provides power up/down glitch free protection during power sequencing.
The DS3884A has two types of power connections in addition to the LI pin. They are the Logic Vcc (Vcc) and the Quiet Vcc (QVcc). There are two Vcc pins on the DS3884A that provide the supply voltage for the logic and control circuitry. Multiple connections are provided to reduce the effects of package inductance and thereby minimize switching noise.
As these pins are common to the Vcc bus internal to the device, a voltage difference should never exist between these pins and the voltage difference between Vcc and QVcc should never exceed +0.5V because of ESD circuitry. Additionally, the ESD circuitry between the Vcc pins and all other pins except for BTL I/Os and LI pins requires that any voltage on these pins should not exceed the voltage on Vcc + 0.5V.
There are three different types of ground pins on the DS3884A. They are the Logic ground (GND), BTL grounds (B1GND-B6GND) and the Bandgap reference ground (QGND). All of these ground reference pins are isolated within the chip to minimize the effects of high current switching transients. For optimum performance the QGND should be returned to the connector through a quiet channel that does not carry transient switching current. The GND and B1GND-B6GND should be connected to the nearest backplane ground pin with the shortest possible path.
Since many different grounding schemes could be implemented and ESD circuitry exist on the DS3884A, it is important to note that any voltage difference between ground pins, QGND, GND or B1GND-B6GND should not exceed +0.5V including power up/down sequencing. Additional transceivers included in the Futurebus+ family are; the DS3886A, BTL 9-bit Latching Data Transceiver, the DS3885 BTL Arbitration transceiver with arbitration competition logic for the AB<7:0>/ABP signal lines, and the featuring edge triggered latches in the driver which may be bypassed during a fall-through mode and a transparent latch in the receiver.
The DS3875 Arbitration Controller included in the Futurebus+ family supports all the required and optional modes for Futurebus+ arbitration protocol. It is designed to be used in conjuction with the DS3884A and DS3885 transceivers.
The DS3805 (LIFE) is a high performance Futurebus+ Protocol Controller. The DS3805 will handle all handshaking signals between the Futurebus+ and the local bus interface. All of the transceivers are offered in 48-pin CERPAC package. ...
|
